The TF08A series secures small-diameter hoses to fittings. A compact, one-piece stainless steel band bears directly on the hose and tightens as the single ear is crimped. The formed ear can be checked visually after installation. Select the clamp using the assembled hose outside diameter at the clamping location and allow clearance for axial fitting and pincer access.
The band is made of stainless steel. Figure 1 shows the clamp before crimping. D denotes clamp outside diameter, T band thickness, H band width and A the inside ear width before crimping. Refer to the part drawing for dimensions, tolerances, material grade and edge requirements.
Figure 1 Pre-Crimp Geometry and Dimension Symbols
Seat the hose on the fitting and measure the hose outside diameter at the clamping location before crimping. Shortlist parts using the assembly diameter limits and the size ranges in the table, then check access for sliding the clamp on and for positioning the jaws. Include both ends of the assembly tolerance range in trial builds.
The pincer jaws draw the two sides of the ear together at its base, reducing the band circumference. If the inside ear width A is used to approximate effective circumferential travel, the theoretical maximum diameter reduction is about A/π. Ear deformation, hose compression and fitting support affect the actual reduction. Establish the crimp settings and acceptance limits in trial builds.
Slide the clamp onto the hose from the end before inserting the fitting. Move it into the specified clamping zone. Check that the band sits squarely, its edges are free of burrs that could damage the hose and the ear is accessible. Align matched pincer jaws at the base of the ear and crimp in one stroke at the validated closing force.
Closing force is the force the installation tool applies to the ear, measured in newtons (N). Set and validate it on the actual assembly using band dimensions, hose wall thickness and hardness, fitting support and the required compression.
Check clamp position, ear formation and hose condition. Check installed dimensions or the residual ear gap against the approved criteria. Perform leak or axial pull-off tests as required by the application. The formed ear provides a visual check. Verify joint performance using the specified acceptance criteria.
The unlined design leaves a local interruption in band contact beneath the ear. Evaluate a lined version if the hose is prone to indentation or the joint requires more continuous circumferential contact. If an assembly fails inspection, follow the approved rework procedure. Do not re-crimp the same ear.
Specify the TF08A part number, quantity, assembled hose diameter limits and hose and fitting details. Include a drawing for any specific material grade, D/T/H/A tolerances, ear profile or edge requirements.
The TF08A series uses a stainless steel band. The listed sizes span 3.3–30.7 mm across the series. When ordering, confirm the size range and initial inside ear width A for the specific Towin part number.
| Part number | A(mm) Inside ear width |
Size range(mm) | Part number | A (mm) Inside ear width |
Size range(mm) |
| TF08A0001 | 2.5 | 3.3–4.1 | TF08A0023 | 6.5 | 11.8–13.8 |
| TF08A0002 | 3 | 3.8–4.6 | TF08A0024 | 6.5 | 12–14 |
| TF08A0003 | 3.2 | 4.1–5.1 | TF08A0025 | 6.5 | 12.5–14.5 |
| TF08A0004 | 3.2 | 4.6–5.6 | TF08A0026 | 6.5 | 13–15 |
| TF08A0005 | 3.2 | 5.1–6.1 | TF08A0027 | 6.5 | 13.5–15.5 |
| TF08A0006 | 3.2 | 5.6–6.6 | TF08A0028 | 7 | 13.8–16 |
| TF08A0007 | 3 | 6.1–7 | TF08A0029 | 8 | 14–16.5 |
| TF08A0008 | 3.5 | 6.5–7.5 | TF08A0030 | 7 | 14.6–16.8 |
| TF08A0009 | 4 | 6.8–8 | TF08A0031 | 7 | 15.3–17.5 |
| TF08A0010 | 4 | 7.1–8.3 | TF08A0032 | 7 | 16.3–18.5 |
| TF08A0011 | 4 | 7.5–8.7 | TF08A0033 | 7.5 | 17.2–19.5 |
| TF08A0012 | 5 | 7.5–9 | TF08A0034 | 7.5 | 17.7–20 |
| TF08A0013 | 5 | 8.1–9.5 | TF08A0035 | 9 | 17.9–20.7 |
| TF08A0014 | 5 | 8.5–10 | TF08A0036 | 7.5 | 18.7–21 |
| TF08A0015 | 5 | 9.1–10.5 | TF08A0037 | 7.5 | 19.5–21.8 |
| TF08A0016 | 5.5 | 9.3–11 | TF08A0038 | 8.5 | 19.9–22.5 |
| TF08A0017 | 5.5 | 9.6–11.3 | TF08A0039 | 8.5 | 21–23.5 |
| TF08A0018 | 5.5 | 10.1–11.8 | TF08A0040 | 9 | 21.7–24.5 |
| TF08A0019 | 6.5 | 10.1–12 | TF08A0041 | 9 | 22.7–25.5 |
| TF08A0020 | 6.5 | 10.3–12.3 | TF08A0042 | 8.5 | 23.6–26.3 |
| TF08A0021 | 6.5 | 10.8–12.8 | TF08A0043 | 9.5 | 24.1–27 |
| TF08A0022 | 6.5 | 11.3–13.3 | TF08A0044 | 11 | 27.2–30.7 |
You can get a price or send us any questions to get any information you would like to know, and we will reply to you as soon as possible.